28.06.2022 by Prof. Dr. Ing. Sascha Englich

Epoxy Resins – Reactive Polymers as a Basis for Injection-Moldable Compounds

Material analysis is of great importance for component as well as mold and process design in the automotive industry. Read, how differential scanning calorimetry contribute to the optimization of epoxy resin injection molding and learn in our second blogarticle of this new blog series even more about injection-moldable compounds.

Prof. Dr. Ing. Sascha Englich is a professor of plastics engineering at the Steinbeis University of Berlin. As part of a new blog series on the optimization of epoxy resin injection molding using differential scanning calorimetry, he explains today, amongst others, the difference between uncured and cross-linked material state and talks about simulation models.

Epoxy resins are not as unfamiliar to us as they first appear. After all, anyone who has ever repaired anything with a 2-component adhesive is already familiar with this material and its particular features. Thereby, a resin is mixed with a hardener (figure 7, left), thus setting a chemical cross-linking reaction (figure 4, center) – i.e., the curing process – in motion. Components generally designated as “carbon fiber” or “carbon” are also based on systems such as these epoxy resin-hardeners. In this case, they, which here also serve as an adhesive, initially infiltrating the fiber bundles during production and forming a firm bond. However, the same chemical principle of resin and hardener can be found in thermoset molding compounds for injection molding (figure 7 on the right), already described in our first article by May 11th, “Thermoset Injection Molding in E-Mobility”. Here, too, a resin-hardener system was discussed, but adjusted such that it occurred as a solid and exhibited almost no chemical reaction at moderate temperatures (slightly cooled to room temperature). Therefore, these materials can be manufactured as ready-compounded molding materials (resin, hardener, filler and reinforcing materials, additives, etc.) in a granulate form and stored for a certain time. Only at elevated temperatures does the chemical cross-linking reaction set in at an accelerated rate, which can be taken advantage of in the processing of heated injection molds.

Fig. 1: 2-component epoxy resin adhesive (left); chemical cross-linking principle of an epoxy resin hardener system (example); epoxy resin molding compound (right).

This material setup, initially consisting of a resin and hardener which then combine to form a 3-dimensional network, also offers the ability to investigate the material structure and its changes by means of thermoanalytical methods (e.g., DSC). 

Uncured Versus Cross-Linked Material State

Here, a differentiation must be made between the uncured and the cross-linked material state. The uncured, oligomer resin is present in the amorphous state so that the phase transformation from solid to liquid (Temperatura di transizione vetrosaLa transizione vetrosa è una delle più importanti proprietà chimico-fisiche dei materiali amorfi e semi-cristallini, come, ad esempio, vetri, metalli (amorfi), polimeri, ingredienti farmaceutici e alimentari e definisce l’intervallo di temperatura in cui le proprietà meccaniche die materiali variano da duro e fragile a più morbido, malleabile o gommoso.glass transition) can be measured by means of DSC analysis (Differential Scanning Calorimetry). In the signal of the heat flow, a “step” occurs (in figure 2, approximately between 60°C and 90°C). The reason for this is the material’s change in Specific Heat Capacity (cp)Heat capacity is a material-specific physical quantity, determined by the amount of heat supplied to specimen, divided by the resulting temperature increase. The specific heat capacity is related to a unit mass of the specimen.specific heat capacity during phase transformation. Evaluation of the step describes the glass transition range with glass transition temperature TG_0 (figure 2, glass transition) of the uncured resin, thus giving an initial indication of the lower processing temperature necessary for plasticizing in the injection molding machine.

Looking at the further progression of the heat-flow signal, an EsotermicoUna transizione o reazione è esotermica se il materiale genera calore exothermal effect occurs at higher temperatures, represented as a peak (figure 2, complex peak [ISO]). This exothermal peak characterizes the chemical cross-linking reaction with the peak area representing the heat of reaction and the integral of the reaction enthalpy. The course of the integral (figure 2, evaluation routine using peak integral) describes the cross-linking process. If the peak integral is derived as a function of time (da/dt), the reaction dynamics are obtained. From the processing point of view, for example, an upper temperature limit for plasticizing can be derived from the starting point of the exothermal peak, and an optimal tool temperature can be derived from the integral’s peak.

Fig. 2: DSC analysis of an epoxy resin compound (uncured), exo ⬆

Figure 3 depicts the different results of the DSC analysis for an epoxy resin in various cross-linking states. As already described before, the uncured starting material (Figure 3, upper graph) shows a clear glass transition range with glass transition temperature of TG_0 as well as the subsequent exothermal cross-linking peak. The integral of the peak (area) describes the total cross-linking enthalpy.

The graph in the middle of figure 3 shows the DSC signal of an injection-molded component, but with incomplete cross-linking. A glass transition range can no longer be recognized since it continues to increase dynamically during the measurement with the Post Crystallization (Cold Crystallization)The post crystallization of semi-crystalline plastics occurs primarily at elevated temperatures and increased molecular mobility above the glass transition.post-crystallization starting at elevated temperatures. As already indicated, the exothermal peak describes post-cross-linking or residual cross-linking. From the ratio of the entire cross-linking enthalpy and the residual cross-linking enthalpy, the degree of cross-linking can be determined:

In In the example shown, the component’s degree of cure amounts to around 81%; i.e., the injection molding process should be optimized again in this case.

The lowest graph in figure 3 depicts the DSC signal of an entirely cross-linked component. Since no further chemical cross-linking reaction occurs, there is also no exothermal effect to observe. In theory, the glass transition at complete curing, TG_1, can be determined instead. However, in the case of injection molding compounds which are typically very highly filled, this is so little pronounced that the determination is not always reliable, especially since the evaluation range for TG_1 often overlaps with the range of thermal degradation. This becomes visible as an exothermal curve increase at very high temperatures (shaded area beginning at approx. 270°C). Therefore, determination of the glass transition temperature of cured components by means of DSC is not recommended. Thermomechanical analysis (TMA) or Dynamic Mechanical Analysis (DMA) would be much better solutions to this end.

Figure 3: DSC analyses of epoxy resin molding compounds in different cross-linking states: uncured (top), incompletely cross-linked (middle), entirely cross-linked (bottom), exo ⬆

Reaction Dynamics for Simulation

Besides using DSC analysis for testing the curing state, it also serves as a basis for generating material data for process and curing simulations. To this end, several DSC analyses are carried out at different heating rates (figure 4 and figure 5) and then the courses of the reaction dynamics are transferred into mathematical models. For injection molding of epoxy compounds, for example, the so-called Kamal-Sourour model is widely used:

In simulation, such models now allow for computation of any cross-linking scenarios as a function of time and temperature. Data fitting can be performed, for example, by means of NETZSCH Kinetics Neo as shown in figure 6.

Figure 4: DSC analysis of an epoxy resin molding compound at different heating rates for mathematical presentation of the reaction dynamics, exo ⬆
Figure 5: Determination of the time- and temperature-dependent cross-linking courses by integrating the exothermal reaction peaks at different heating rates
Figure 6: NETZSCH Kinetics Neo: Reaction dynamics in mathematical models for simulation

With regard to sample preparation for epoxy resin-based injection molding compounds, the following procedure has become established: Aluminum crucibles/lids are used, with the lids being pierced. (For other types of molding compounds such as those based on phenolic resins, special pressure-tight crucibles should be used.) The granules are ground to a powder, if possible without thermal signature, and “carefully” pressed into the crucible (figure 14). This significantly increases contact with the crucible bottom as well as the thermal conduction within the sample, leading to consistent and reproducible DSC curves.

Figure 7: Sample preparation of epoxy resin molding compounds for injection molding

Learn more about the curing optimization using DSC in the next blog article of our new blog series by Dr. Sascha Englich.

For more information in advance, go to NETZSCH Analyzing & Testing.